Medication-info.com Search Menu

Mebrofenin Injection 10 mg Package Insert

Status:
Prescription (Rx) Facts
Strength:
10 mg
Active ingredient:

Prescribing information (package insert) - Mebrofenin Injection 10 mg

DESCRIPTION

AnazaoHealth supplies compounded Mebrofenin for the preparation of Tc-99m Mebrofenin. Each reaction vial contains 10 mg Mebrofenin and 0.2 mg tin as stannous chloride. The vial is back filled with nitrogen gas after lyophilization. The vial may contain a partial vacuum.

INDICATIONS AND USAGE

Technetium Tc-99m Mebrofenin by intravenous administration is indicated as a hepatic imaging agent, used in the diagnosis of liver disease

DOSAGE AND ADMINISTRATION

The suggested intravenous dose range of Technetium Tc 99m Mebrofenin in the average patient (70 kg) is:

Nonjaundiced patient: 74 - 185 MBq (2-5 mCi)

Patient with serum bilirubin level greater than 1.5 mg/dL: 111-370 MBq (3-10 mCi)

The patient should be in a fasting state, 4 hours is preferable. False positives (non-visualization) may result if the gallbladder has been emptied by ingestion of food.

An interval of at least 24 hours should be allowed before repeat examination

PREPARATION

To prepare injection, follow this aseptic procedure:

  1. 1. Waterproof gloves should be worn during the preparation procedure.
  2. 2. Snap off the plastic lid and place room temperature reaction vial in an appropriate lead shield.
  3. 3. Swab the rubber closure of the vial with a germicide.
  4. 4. Inject 1 – 3 ml Sterile additive free sodium pertechnetate Tc-99m injection containing up to 740 MBq (20 mCi) into the vial. Be sure to maintain inert atmosphere in vial by introducing as little air as possible during reconstitution. NOTE: If sodium pertechnetate Tc-99m injection must be diluted, use only preservative free Sodium Chloride Injection USP.
  5. 5. Secure the lead shield cover. Swirl the vial gently to mix contents and let stand 3 to 5 minutes prior to use.
  6. 6. Record the date and time of preparation on a pressure-sensitive label.
  7. 7. Affix pressure-sensitive label to shield.
  8. 8. Examine vial contents; if the solution is not clear and free of particulate matter and discoloration on visual inspection, it should not be used.
  9. 9. Measure the radioactivity by suitable calibration system and record prior to patient administration.
  10. 10. Appropriate quality control is recommended.
  11. 11. Use within 12 hours of preparation

About this document

Source: FDA drug labeling via NLM DailyMed · View the label on DailyMed

Found a mistake? Write to us via the contact page.

The information on this site does not replace the advice of a doctor or pharmacist.

Drug information for Mebrofenin Injection 10 mg

Rx or OTC
Prescription (Rx)?
  • This drug is available only with a prescription from a licensed healthcare provider.
  • Rx
Active ingredient Mebrofenin 10 mg
Dosage form Injection, powder, lyophilized, for solution
Route Intravenous
Marketing status not in the current FDA NDC Directory
Company (applicant) AnazaoHealth Corporation
FDA approval UNAPPROVED DRUG OTHERUnapproved drug
Manufacturers 1 labelers list this drug on DailyMed
Packages (NDC)
Package
10 mg – 1 in 1 kit NDC 51808-216-01

Source: FDA drug labeling via NLM DailyMed, data as of October 31, 2026. FDA data (DailyMed, Orange Book, Drug Shortages, enforcement reports). Not a substitute for the advice of a doctor or pharmacist.